266 lines
9.3 KiB
C
266 lines
9.3 KiB
C
/*
|
|
* Copyright (c) 2020 The ZMK Contributors
|
|
*
|
|
* SPDX-License-Identifier: MIT
|
|
*/
|
|
|
|
#define DT_DRV_COMPAT issi_is31fl3741
|
|
|
|
#include <zephyr.h>
|
|
#include <device.h>
|
|
#include <drivers/gpio.h>
|
|
#include <drivers/i2c.h>
|
|
#include <drivers/led_strip.h>
|
|
#include <logging/log.h>
|
|
#include <sys/math_extras.h>
|
|
#include <sys/util.h>
|
|
|
|
LOG_MODULE_DECLARE(zmk, CONFIG_ZMK_LOG_LEVEL);
|
|
|
|
#define IS31FL3741_BUFFER_SIZE (39 * 9)
|
|
#define IS31FL3741_BUFFER_PAGE_BREAK (0xb4)
|
|
|
|
#define IS31FL3741_REG_PS (0xfd)
|
|
#define IS31FL3741_REG_PSWL (0xfe)
|
|
|
|
#define IS31FL3741_PSWL_ENABLE (0xc5)
|
|
#define IS31FL3741_PSWL_DISABLE (0x00)
|
|
|
|
#define IS31FL3741_PAGE_PWM_A (0x00)
|
|
#define IS31FL3741_PAGE_PWM_B (0x01)
|
|
#define IS31FL3741_PAGE_SCALING_A (0x02)
|
|
#define IS31FL3741_PAGE_SCALING_B (0x03)
|
|
#define IS31FL3741_PAGE_FUNCTION (0x04)
|
|
|
|
struct is31fl3741_config {
|
|
char *bus;
|
|
int reg;
|
|
char *label;
|
|
char *sdb_port;
|
|
gpio_pin_t sdb_pin;
|
|
gpio_dt_flags_t sdb_flags;
|
|
uint8_t *px_buffer;
|
|
size_t px_buffer_size;
|
|
uint8_t gcc;
|
|
uint8_t sws;
|
|
uint16_t *rgb_map;
|
|
};
|
|
|
|
struct is31fl3741_data {
|
|
const struct device *i2c;
|
|
const struct device *gpio;
|
|
};
|
|
|
|
static int is31fl3741_reg_write(const struct device *dev, uint8_t addr, uint8_t value) {
|
|
const struct is31fl3741_data *data = dev->data;
|
|
const struct is31fl3741_config *config = dev->config;
|
|
|
|
if (i2c_reg_write_byte(data->i2c, config->reg, addr, value)) {
|
|
LOG_ERR("Failed writing value %x to register address %x on device %x.", value, addr,
|
|
config->reg);
|
|
return -EIO;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int is31fl3741_reg_burst_write(const struct device *dev, uint8_t start_addr,
|
|
const uint8_t *buffer, size_t num_bytes) {
|
|
const struct is31fl3741_data *data = dev->data;
|
|
const struct is31fl3741_config *config = dev->config;
|
|
|
|
if (i2c_burst_write(data->i2c, config->reg, start_addr, buffer, num_bytes)) {
|
|
LOG_ERR("Failed burst write with starting address %x", start_addr);
|
|
return -EIO;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int is31fl3741_set_page(const struct device *dev, uint8_t page_addr) {
|
|
if (is31fl3741_reg_write(dev, IS31FL3741_REG_PSWL, IS31FL3741_PSWL_ENABLE)) {
|
|
return -EIO;
|
|
}
|
|
|
|
if (is31fl3741_reg_write(dev, IS31FL3741_REG_PS, page_addr)) {
|
|
return -EIO;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static inline bool num_pixels_ok(const struct is31fl3741_config *config, size_t num_pixels) {
|
|
size_t num_bytes;
|
|
|
|
const bool overflow = size_mul_overflow(num_pixels, 3, &num_bytes);
|
|
|
|
return !overflow && (num_bytes <= config->px_buffer_size);
|
|
}
|
|
|
|
/**
|
|
* Updates individual LED channels without an RGB interpretation.
|
|
*/
|
|
static int is31fl3741_strip_update_channels(const struct device *dev, uint8_t *channels,
|
|
size_t num_channels) {
|
|
const struct is31fl3741_config *config = dev->config;
|
|
|
|
if (config->px_buffer_size < num_channels) {
|
|
return -ENOMEM;
|
|
}
|
|
|
|
is31fl3741_set_page(dev, IS31FL3741_PAGE_PWM_A);
|
|
|
|
int result;
|
|
|
|
result = is31fl3741_reg_burst_write(
|
|
dev,
|
|
0x00,
|
|
channels,
|
|
(num_channels <= IS31FL3741_BUFFER_PAGE_BREAK) ? num_channels : IS31FL3741_BUFFER_PAGE_BREAK);
|
|
|
|
if (result || num_channels <= IS31FL3741_BUFFER_PAGE_BREAK) {
|
|
return result;
|
|
}
|
|
|
|
is31fl3741_set_page(dev, IS31FL3741_PAGE_PWM_B);
|
|
|
|
return is31fl3741_reg_burst_write(dev, 0x00, channels + 0xb4, num_channels - 0xb4);
|
|
}
|
|
|
|
/*
|
|
* Updates the RGB LED matrix according to devicetree's map property.
|
|
*/
|
|
static int is31fl3741_strip_update_rgb(const struct device *dev, struct led_rgb *pixels,
|
|
size_t num_pixels) {
|
|
const struct is31fl3741_config *config = dev->config;
|
|
|
|
uint8_t *px_buffer = config->px_buffer;
|
|
uint16_t *rgb_map = config->rgb_map;
|
|
|
|
size_t i = 0;
|
|
size_t j = 0;
|
|
|
|
if (!num_pixels_ok(config, num_pixels)) {
|
|
return -ENOMEM;
|
|
}
|
|
|
|
while (i < num_pixels) {
|
|
px_buffer[rgb_map[j++]] = pixels[i].r;
|
|
px_buffer[rgb_map[j++]] = pixels[i].g;
|
|
px_buffer[rgb_map[j++]] = pixels[i].b;
|
|
|
|
++i;
|
|
}
|
|
|
|
return is31fl3741_strip_update_channels(dev, px_buffer, config->px_buffer_size);
|
|
}
|
|
|
|
/*
|
|
* Initiates a driver instance for IS31FL3741.
|
|
*
|
|
* SDB is pulled high to enable chip operation followed
|
|
* by a reset to clear out all previous values.
|
|
*
|
|
* Function and scaling registers are then pre-configured based on devicetree settings.
|
|
*/
|
|
int static is31fl3741_init(const struct device *dev) {
|
|
struct is31fl3741_data *data = dev->data;
|
|
const struct is31fl3741_config *config = dev->config;
|
|
|
|
data->i2c = device_get_binding(config->bus);
|
|
|
|
if (data->i2c == NULL) {
|
|
LOG_ERR("I2C device %s not found", config->bus);
|
|
return -ENODEV;
|
|
}
|
|
|
|
data->gpio = device_get_binding(config->sdb_port);
|
|
|
|
if (data->gpio == NULL) {
|
|
LOG_ERR("GPIO device %s not found", config->sdb_port);
|
|
return -ENODEV;
|
|
}
|
|
|
|
gpio_pin_configure(data->gpio, config->sdb_pin, (GPIO_OUTPUT | config->sdb_flags));
|
|
|
|
if (gpio_pin_set(data->gpio, config->sdb_pin, 1)) {
|
|
LOG_ERR("SDB pin for %s cannot be pulled high", config->label);
|
|
return -EIO;
|
|
}
|
|
|
|
// Set configuration registers
|
|
if (is31fl3741_set_page(dev, IS31FL3741_PAGE_FUNCTION)) {
|
|
LOG_ERR("Couldn't switch to function registers on %s", config->label);
|
|
return -EIO;
|
|
}
|
|
|
|
// Reset
|
|
is31fl3741_reg_write(dev, 0x3f, 0xae); // Reset
|
|
|
|
// Re-set configuration registers
|
|
if (is31fl3741_set_page(dev, IS31FL3741_PAGE_FUNCTION)) {
|
|
LOG_ERR("Couldn't switch to function registers on %s", config->label);
|
|
return -EIO;
|
|
}
|
|
|
|
// Configure LED driver operation mode
|
|
is31fl3741_reg_write(
|
|
dev, 0x00, (config->sws << 4) | (0x01 << 3) | 0x01); // SWS, H logic, Normal operation
|
|
is31fl3741_reg_write(dev, 0x01, config->gcc); // Set GCC
|
|
|
|
// Set all scaling registers to 0xff, brightness is controlled using PWM
|
|
uint8_t scaling_buffer[0xb4];
|
|
for (size_t i = 0; i < 0xb4; ++i) {
|
|
scaling_buffer[i] = 0xff;
|
|
}
|
|
|
|
if (is31fl3741_set_page(dev, IS31FL3741_PAGE_SCALING_A)) {
|
|
LOG_ERR("Couldn't switch to scaling register A on %s", config->label);
|
|
}
|
|
|
|
is31fl3741_reg_burst_write(dev, 0x00, scaling_buffer, 0xb4);
|
|
|
|
if (is31fl3741_set_page(dev, IS31FL3741_PAGE_SCALING_B)) {
|
|
LOG_ERR("Couldn't switch to scaling register B on %s", config->label);
|
|
}
|
|
|
|
is31fl3741_reg_burst_write(dev, 0x00, scaling_buffer, 0xab);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct led_strip_driver_api is31fl3741_api = {
|
|
.update_rgb = is31fl3741_strip_update_rgb,
|
|
.update_channels = is31fl3741_strip_update_channels,
|
|
};
|
|
|
|
#define IS31FL3741_GCC(idx) \
|
|
(DT_INST_PROP(idx, r_ext) * DT_INST_PROP(idx, led_max_current) * 256 * 256) / (383 * 255)
|
|
|
|
#define IS31FL3741_DEVICE(idx) \
|
|
\
|
|
static struct is31fl3741_data is31fl3741_##idx##_data; \
|
|
\
|
|
static uint8_t is31fl3741_##idx##_px_buffer[IS31FL3741_BUFFER_SIZE]; \
|
|
\
|
|
static uint16_t is31fl3741_##idx##_rgb_map[IS31FL3741_BUFFER_SIZE] = DT_INST_PROP(idx, map); \
|
|
\
|
|
static const struct is31fl3741_config is31fl3741_##idx##_config = { \
|
|
.bus = DT_INST_BUS_LABEL(idx), \
|
|
.reg = DT_INST_REG_ADDR(idx), \
|
|
.label = DT_INST_LABEL(idx), \
|
|
.sdb_port = DT_INST_GPIO_LABEL(idx, sdb_gpios), \
|
|
.sdb_pin = DT_INST_GPIO_PIN(idx, sdb_gpios), \
|
|
.sdb_flags = DT_INST_GPIO_FLAGS(idx, sdb_gpios), \
|
|
.px_buffer = is31fl3741_##idx##_px_buffer, \
|
|
.px_buffer_size = IS31FL3741_BUFFER_SIZE, \
|
|
.gcc = IS31FL3741_GCC(idx), \
|
|
.sws = DT_INST_PROP(idx, sw_setting), \
|
|
.rgb_map = is31fl3741_##idx##_rgb_map, \
|
|
}; \
|
|
\
|
|
DEVICE_AND_API_INIT(is31fl3741_##idx, DT_INST_LABEL(idx), &is31fl3741_init, \
|
|
&is31fl3741_##idx##_data, &is31fl3741_##idx##_config, POST_KERNEL, \
|
|
CONFIG_LED_STRIP_INIT_PRIORITY, &is31fl3741_api);
|
|
|
|
DT_INST_FOREACH_STATUS_OKAY(IS31FL3741_DEVICE);
|